Telephone: (607) 589-6160 Fax: (607) 589-4026 Email: info@northeastimplement.com
|
Telephone: (607) 589-6160 Fax: (607) 589-4026 Email: info@northeastimplement.com |
|
Northeast Implement Corporate Home Page VALBY Log, Sorting and Demolition Grapples VALBY Log Grapple for Skidsteer Electric Motor or Engine Driven Wood Chippers
|
Valby CH222HF Woodchipper A Chipper for Highway Departments The Valby CH 222 woodchipper is designed for efficient and safe disposal of stems, branches and bushes along roadsides. The chips can be blown into a truck or back to the roadside. The chipper is fed from the right side so the feed is close to the material to be chipped. The operator stands on the road, away from the ditch and the traffic. The feed chute does not stick outside the width of the tractor. The tractor can therefore be driven safely on the right side of the road without risk of the feed chute hitting road signs or railings. The aggressive power feed makes the CH 222HF also the perfect machine for Christmas tree disposal. A Chipper For Orchards The Valby CH 222HF is easy to use in orchards. It can be maneuvered between narrow rows as neither the feed nor the discharge chutes stick out beyond the width of the tractor.
Valby CH222 HF Ease of Operation The low feeding point ensures effortless feeding of the chipper. The operator can stand with a straight back. The discharge direction is adjustable 360 degrees.The chipper is easy to move between locations as the feed chute will fold up so it will not stick outside the width of the tractor. The chipper stands up by itself on the ground and is easy to hook up or remove from the tractor. Power Requirements Due to the inertia of the heavy and large rotor, power units down to 35 HP can be used. About 7 HP is required for every inch of round wood diameter. Thus, to chip a 5-inch round wood, you need a 35 HP tractor (7 X 5 = 35). Safety Features The Valby chippers do not have any knife motion toward the operator-this reduces the risk of loose material flying back through the feed chute. The knives are counter-sunk into the disk, so the stress of chipping is absorbed by the entire backside of the knife, not just the knife bolts. The discharge height is 7'11" above ground so the discharge is above eye level. To accomplish safe operation in various wind directions, the Valby chipper's discharge direction is adjustable 360 degrees. The deflector bonnet enables placing the chips near or far. The Valby chippers also have several noise-reducing features. The discharge opening is above ear level. It is adjustable and can be directed away from the operator. The hydraulic feed rollers cover the feed opening, thus reducing the noise level. The air intake is on the tractor side so the noise from the chipping is directed away from the operator.
Hydraulic Power Feed The hydraulic feed is powered from the outlets on the tractor. The operator can select feed, stop and reverse from the bar on top of the feed chute. The turning speed of the rollers is continuously adjustable from a knob on the hydraulic valve. The bottom feed roller is fixed. The top roller is spring loaded. The spring tension is adjustable. The material is squeezed between the two rollers The hydraulic feed chutes are close to the ground so quite heavy trees can be manually fed into the chipper. Minimum oil requirement is 4 GPM; maximum 18 GPM. The oil might heat up if the reservoir is small. If the oil reservoir is under 10 gallons, the operator should check for eventual overheating. An oil cooler should be installed on the return line in case of overheating. The feed rollers of the Valby PTO woodchipper are powered by two 24 cu inch hydraulic motors. They provide a combined 10 HP of pulling power. The bottom feed roller is fixed in place. The top feed roller had a hinge and it climbs on top of the stem and pulls it to the knives. There is a large spring (seen in the middle of the picture) which puts down pressure on the top feed roller so it bites into the stem. The down pressure can be adjusted to the users' needs by changing the springs location on the lever. |
|
Send mail to info@northeastimplement.com with questions regarding our products, or call (607) 589-6160. Including your name and address will help us to locate a dealer near you. Fax: (607) 589-4026. Mail: 460 Halsey Valley Road, Spencer N.Y. 14883. |
